K14
Design: Norbert Wangen
K14 is a system of base units without handles where the opening of the fronts and doors is accessible thanks to the 30° bevelled edge, the same as the worktop, thus creating an ethereal effect of suspension and lightness. The new design of K14 is integrated in 2024 with two end panels on the sides with the same section as the top, shaping a practical snack section, a portal that overlooks the marble backs that do not touch the ground, but graze it by just two centimetres. The opening of the K14 fronts occurs through a 30° bevel, both in the base units and in the wall units. This design detail not only facilitates use, but also creates a feeling of suspension and lightness, combining functionality and beauty.
Refined aesthetics and high quality material
The composition of K14 is elegant and minimal, enhancing the aesthetics of the chosen material. From the refinement of wood to the elegance of steel, from marble to Corian®, each material is chosen for its quality and ability to integrate perfectly into the design.
Important overhangs and innovative structure
K14 offers the possibility of having significant overhangs, with a 45° bevel, thanks to its aluminum structure designed to support the overhang with extreme stability and safety.
K14 is much more than a kitchen: it is a work of art of modern design. Norbert Wangen has created a kitchen that adapts perfectly to contemporary needs, offering a solution that combines innovation, elegance and functionality. With K14 he continues to set new standards in luxury kitchen design.
Technical Details
BASE UNITS
Characteristics
Made of 19 mm thick wood particle board panels, suitable for damp spaces indoors and with low formaldehyde emission, treated with high performance melamine resin.
Height
790 MM
Depth
380 / 725 MM
Width
300 / 450 / 600 / 900 / 1200 MM
Finishes
-
THERMO-TREATED LARCH WOOD
-
ELM WOOD
-
GREY-GRAPHITE OAK
K14
Thickness 23 mm
K14
Thickness 50 mm
HANDLE RAIL
The range of Boffi materials and their compatibility with individual products are constantly evolving: check with your dealer for the actual availability of the product in the desired finish.
Solvent-based matt lacquer. Features: • Solvent-base polyurethane coating • Base coat of polyester. • One paint coat, cross-applied
LEEDS GREY
CORTINA WHITE
Water-based textured matt lacquer. The following features make SILCOLAK a top-quality finish: • Water-based textured paint, bi-component and undiluted (not contaminated by external agents), designed and produced exclusively for Boffi. • Colour range, exclusive for Boffi. • Excellent chemical and physical resistance (tested in laboratories). • Very low yellowing effect over time. • Coat of isolating paint Primer and double layers of polyester plastering, ideal for reducing small imperfections on surfaces and allowing a better coverage. • Base coat of polyester. • Coat of isolating paint Primer for corners and edges. • Two paint coats, cross-applied.
RED RIBES
JET BLACK
ABYSS BLACK
SLATE GREY
SLIT
ROPE
HAY
GRAVEL GREY
LUTON GREY
OYSTER-PEARL
PAROS WHITE
SIBERIA WHITE
MYRTUS GREEN
Water-based “soft touch” matt lacquer. Features: The following features make ECOLAK a top-quality finish: • Water-based “soft touch” paint, bi-component and undiluted (not contaminated by external agents), designed and produced exclusively for Boffi. • Colour range, exclusive for Boffi. • Excellent chemical and physical resistance – tested in laboratories. • Very low yellowing effect over time. • Coat of isolating paint Primer and double layers of polyester plastering, ideal for reducing small imperfections on surfaces and allowing a better coverage. • Base coat of polyester. • Coat of isolating paint Primer for corners and edges. • Two paint coats, cross-applied.
BLACK
CHARCOAL
BASALT GREY
MUD
ÈCRU
OAT
PEBBLE GREY
CLOUD
MAGNOLIA
WARM WHITE
ARTIC WHITE
Nanotechnological matt “soft touch” FENIX NTM® surface. FENIX NTM® The exterior decorative surface is obtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view. FENIX NTM® UNICOLOR Obtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view (colour-core).
BEIGE LUXOR
BEIGE ARIZONA
INGO BLACK
ORINOCO COCOA
BLUE FES
BROMO GREY
JAIPUR RED
COMODORO GREEN
LONDON GREY
ANTRIM GREY
EFESO GREY
MALÈ WHITE
KOS WHITE
The polyester lacquering is carried out by a process of applying paints on MDF panels, with several coats. The surfaces are sanded with different coarse-grained and fine-grained sandpapers. Then they are polished using brushes impregnated with abrasive wax. The result obtained is a very glossy surface (close to the mirror effect) that reaches 95 gloss. Polyester is a very resistant material, practically waterproof; its surface does not absorb, but is sensitive to scratches. The scratched surface can be re-smoothed and re- polished or even repaired adding material and then by sanding and smoothing it again. Three layers of paint coat each surface, it means 900 g/m2 (ca. 1 mm thick); nine layers of paint coat each edge (ca. 3 mm thick). It is sensitive to light if directly exposed for very long periods. It can slightly change the tone, becoming lighter especially on light tones (family of whites). In case of element additions in a second moment, these tone changes cannot be perfectly replicated and may not match exactly the original shade. This issue cannot be considered cause for a complaint.
FOREST GREY
PETRA RED
JODHPUR BLUE
CALIGO GREEN
MILKY MINT
BLACK
DEEP GREY
ELEGANT GREY
GREY
GREY RAL 7038
SAND
ROPE
PEBBLE GREY
MAGNOLIA
WHITE
Raw clay mixed with resin. The compound is applied by hand with a spatula, creating a very elegant and refined texture that is exclusive and unique for each surface. The manual trowelling may generate slight differences in thickness on the finished product. This process makes each piece unique and unrepeatable.
ARA
SIRIO
PEGASO
LYRA
HYDRA
COLUMBIA
ANDROMEDA
Metal-effect lacquer. Easy Metals is a finishing that reproduces the typical effect of metallic surfaces, obtained by use of metal particles-enriched solvent-based paints. Variations in brightness (halos caused by the spread of the paint metal particles along the surface) make each piece a unique and exclusive.
LEAD CLASS
COPPER DARK
IRON LUXURY
ZINC GLAM
SILVER STYLE
Metal-effect lacquer. Metals is a special finishing which reproduces the typical effect of brushed metallic surfaces, rendered through a very precise and technical sequence of production cycles. The characteristic metallic effect of the surface is given by the alternation of manual and mechanical processes, by the quality of the metal particles-enriched solvent-based paints and by the complex drying procedure. The various shades of colour (halos caused by the spread of the paint chromium particles) and the succession of multi-directional brushing of the surface make each piece a unique and exclusive one.
LEAD RAYÈ
BRONZE RAYÈ
ANCIENT BRONZE RAYÈ
BRONZED BRASS RAYÈ
BRASS RAYÈ
COPPER RAYÈ
LEAD
TITANIUM
COPPER+
VINTAGE BRASS
ZINC+
ALUMINIUM
WHITE
Slats, alternating thickness 20 / 23 mm - Solid wood layers, with support made of strip wood. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. Doors and panels have vertical grain. The “old“ grey pinewood consists of pinewood solid boards recycled from renovation of old houses, barns and huts. The characteristic grey tone of this material is obtained by specific painting cycles, which give the typical “old” aspect to this wood. Possible cracks and deformations have to be considered characteristic part of the product. Since these pieces are very unique, they have the typical appeal of “imperfect things“ and they clearly display sign of times and bad weather; therefore they show deformations and wrinkles strength. Worktops obtained with old wooden boards offer a clear example of the wood vitality and instability. For this reasons each piece in solid wood has to be considered considered “unique“ and different from all the other ones.
SMOKED DYED OAK SW
OLD GREY PINEWOOD
THERMO TREATED OLIVATO ASH WOOD SW
CANALETTO LIGHT WALNUT "SAWN EFFECT"
AMERICAN ELM SW
AISI 304 box section stainless steel sheet, orbital satin (Orbital Steel). It is an irregular steel grain pattern, obtained by using an orbital sander which gives the stainless steel a vintage look. EXCLUSIVE FINISH FOR BOFFI
O_STEEL SILVER
O_STEEL
Natural material extracted from quarry. Matt finish. The natural stones used by Boffi for the production of tops, panels, back panels, sinks, washbasins or bathtubs are always given a dedicated stain and oil-repellent and waterproof treatment to guarantee a high protection.
VERDE ALPI MARBLE
ROSSO LEPANTO MARBLE
ITALIA GREY MARBLE
APPLE BLOSSOM WHITE LASA MARBLE
GREY CARNICO MARBLE
GREY STONE MARBLE
EMPERADOR DARK MARBLE
BLACK COSMIC GRANITE
ABSOLUTE BLACK ZIMBABWE GRANITE
WHITE CARRARA MARBLE
It is a Solid Surface, non-porous and homogeneous, composed for about 1/3 of acrylic resin (polymethyl methacrylate or PMMA) and for about 2/3 of natural minerals consisting mainly of aluminium trihydrate (ATH), which is a mineral extracted from the bauxite used to produce aluminium.
WHITE
Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials.
ECOWOOD TEAK
ECOWOOD DATUK EBONY (10.44)
ECOWOOD INDIAN ROSEWOOD (10.23)
SMOKED OAK
CANALETTO WALNUT U.S.
AMERICAN ELM
ECOWOOD XILO 2.0 STRIPED BLACK (18.04)
ECOWOOD XILO 2.0 PLANKED GREY (18.23)
ECOWOOD XILO 2.0 PLANKED SAND (18.22)
GREY-GRAPHITE-OAK
ASH-GREY-OAK
OAK
FOSSIL OAK
AISI 304 box section stainless steel sheet.
PRE-SATIN
Wood layers, with support made of strip wood. Boffi uses only wood from not primary forests, to guarantee an adequate restoration of the renewable raw materials. Doors and panels have vertical grain. The “old“ grey pinewood consists of pinewood solid boards recycled from renovation of old houses, barns and huts. The characteristic grey tone of this material is obtained by specific painting cycles, which give the typical “old” aspect to this wood. Possible cracks and deformations have to be considered characteristic part of the product. Since these pieces are very unique, they have the typical appeal of “imperfect things“ and they clearly display sign of times and bad weather; therefore they show deformations and wrinkles strength. Worktops obtained with old wooden boards offer a clear example of the wood vitality and instability. For this reasons each piece in solid wood has to be considered considered “unique“ and different from all the other ones.
CANALETTO LIGHT WALNUT
SMOKED DYED OAK SW
OLD GREY PINEWOOD
CANALETTO LIGHT WALNUT "SAWN-EFFECT"
AMERICAN ELM SW
EASYLAK+
SILCOLAK
ECOLAK
LASERMAT
POLYESTER
CLAY
EASY METALS
METALS
SOLID WOOD 3D
O_STEEL
STONE-MARBLE-GRANITE
CORIAN®
WOOD VENEER
STAINLESS STEEL
SOLID WOOD
The range of Boffi materials and their compatibility with individual products are constantly evolving: check with your dealer for the actual availability of the product in the desired finish.
Nanotechnological matt “soft touch” FENIX NTM® surface. FENIX NTM® The exterior decorative surface is obtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view. FENIX NTM® UNICOLOR Obtained starting from thermosetting last generation resins that, thanks to the use of nanotechnology (NTM), make the surface extraordinary from a mechanical, aesthetic and functional point of view (colour-core).
BEIGE LUXOR
BEIGE ARIZONA
INGO BLACK
ORINOCO COCOA
BLUE FES
BROMO GREY
JAIPUR RED
COMODORO GREEN
LONDON GREY
ANTRIM GREY
EFESO GREY
MALÈ WHITE
KOS WHITE
AISI 304 box section stainless steel sheet.
MATT-SATIN
AISI 304 box section stainless steel sheet, orbital satin (Orbital Steel). It is an irregular steel grain pattern, obtained by using an orbital sander which gives the stainless steel a vintage look. EXCLUSIVE FINISH FOR BOFFI
O_STEEL SILVER
O_STEEL
Very compact surface composed of quartz, materials used to produce glass and ceramic, treated with Sinterized Particle Technology and ultra-compaction process.
MICRON
ALBARIUM
ARGENTIUM
ZENITH WHITE
DOMOOS
SIRIUS BLACK
It is a Solid Surface, non-porous and homogeneous, composed for about 1/3 of acrylic resin (polymethyl methacrylate or PMMA) and for about 2/3 of natural minerals consisting mainly of aluminium trihydrate (ATH), which is a mineral extracted from the bauxite used to produce aluminium.
WHITE
Composite material made of high-purity minerals, by using Full Digital technology. “Natural” matt finish. The decorative design is on the front surface only. Features: - Surface: smoother-feeling texture and total control over the design, leading to outstanding visual properties. - Hygienic and nontoxic: Because it has a non-porous surface, this prevents the build-up of bacteria or mould. - Resistant: It is highly resistant to stains, heat, frost, thermal shock, scratches and impacts, ultraviolet rays and has a low water absorption rate. - Ecological: -70% savings on water consumption and -90% reduction in atmospheric emissions during the production process. 50% made with recycled materials.
KANRAN (Exclusive Boffi finish)
SURREY (Exclusive Boffi finish)
DEVON (Exclusive Boffi finish)
BIHARA (Exclusive Boffi finish)
BLACK
GREY
CAMEL
WHITE
Natural material extracted from quarry. Matt finish. The natural stones used by Boffi for the production of tops, panels, back panels, sinks, washbasins or bathtubs are always given a dedicated stain and oil-repellent and waterproof treatment to guarantee a high protection.
QUARTZITE BRECCIA IMPERIALE
VERDE ALPI MARBLE
ROSSO LEPANTO MARBLE
ITALIA GREY MARBLE
QUARTZITE SPIDER BLACK
SUPERWHITE MARBLE
APPLE BLOSSOM WHITE LASA MARBLE
QUARTZITE CALACATTA
GREY CARNICO MARBLE
GREY STONE MARBLE
EMPERADOR DARK MARBLE
BLACK COSMIC GRANITE
ABSOLUTE BLACK ZIMBABWE GRANITE
WHITE CARRARA MARBLE
LASERMAT
STAINLESS STEEL
O_STEEL
DEKTON® COMPOSITE
CORIAN®
MDI COMPOSITE
STONE-MARBLE-GRANITE
PLINTH
Characteristics
Made of extruded aluminium profile.
Height
80 – 100 MM
Finishes
-
STAINLEES STEEL
-
PAINTED MATT WHITE
-
PAINTED MATT BLACK
-
silcolak
-
ecolak
-
clay
-
easy-metals
-
metals
Height
80 MM
Depth
830 / 900 / 980 / 1200 / 1260 / 1500 / 1800 MM
Width
min. 900 MM / max 3000 MM
Request More Info
Complete the Indoor kitchens K14
Projects Made With K14
View More
